Пульт сигнализации MAGICAR

Пульт сигнализации EXECUTIVE


Executive Model One#1 – красный светодиод
Executive Model One#1,2 – красный светодиод
Executive Model One#1,7RS – красный светодиод
Executive Model One#1ATV – красный светодиод
Executive Model One#2ATV – красный светодиод
Executive Model One E-2100ATV – зеленый светодиод
Executive Model One E-2300ATV – зеленый светодиод
Executive Model One E-2500ATV – зеленый светодиод
Executive Model One E-3000ATV – зеленый светодиод

Пульт сигнализации GENERIC


Generic C-4SRS – красный светодиод

Пульт сигнализации K-9


K-9 ONE – красный светодиод
K-9 Five T – красный светодиод

Пульт сигнализации M.A.T


M.A.T – 5t – красный светодиод

Пульт сигнализации AUDIOVOX PRO


PRO-9544FT, 9549FT, 9600FT, 9246FT3, 9342FT3, 9342FT3WOS2, 9642FT3WOS2, 9246FT3, 9342FT3, 9544FT3, 9549FT, 9549FT3, TSP575

Пульт сигнализации GENERIC


Generic AU-REC-2ATV – красный светодиод
Generic REC-8 – красный светодиод
Generic REC-9 – красный светодиод
Generic REC-10 – красный светодиод
Generic SYSTEM 25 – красный светодиод

Пульт сигнализации CRIME GUARD


Crime Guard CG-850i3

Пульт сигнализации GENERIC


Generic C-5
Generic REC-11

Пульт сигнализации FIGHTER


Fighter Revolutoin (дополнительный брелок)

Пульт сигнализации CODE ALARM


Code Alarm серия ELITE
3500, 4000, 5000,5500, 6000, 7000, COMPETITION

Пульт сигнализации CODE ALARM


Code Alarm CA120

Пульт сигнализации CODE ALARM


Code Alarm CA230

Пульт сигнализации CODE ALARM


Code Alarm CA130, CA530, CA630

Пульт сигнализации CODE ALARM


Code Alarm серия ELITE
2000

Пульт сигнализации AUTOPAGE


Модель брелка XT-57
Autopage RF-503

Пульт сигнализации ASTROSTART


Astrostart DE-1003

Пульт сигнализации AUDIOVOX PURSUIT


Модель брелка PROOE4
Для автосигнализаций Pursuit PRO-9744, PRO-9744WOS2

Пульт сигнализации CHECKMATE


Пульт сигнализации COMMANDER


Модели KD-200PC, KD-500, KD-70SPC

Пульт сигнализации Продукция Альтоники.


Пульт сигнализации Тип брелка RFS4-M.

Пульт сигнализации ANACONDA


Anaconda A-300

Пульт сигнализации ANACONDA


Anaconda GS-300, IS-300

Пульт сигнализации ANACONDA


Anaconda GS-430, IS-430

Пульт сигнализации TERMINATOR


Terminator 100, 200

Пульт сигнализации AUTOMATE


Automate 35, 7HF(433MHz)

Пульт сигнализации PYTHON


Python (434MHz) - 440HP, 460HP, 660XP, 1500HF, 2000HF, 3000HF
Python (302MHz) - 70, 80, 90

Пульт сигнализации SIDEWINDER


Sidewinder (434MHz) - 7000HF, 381S, 3200HS, 3300HS, 5500XS, 6500HF
Sidewinder (302MHZ) – 7100, 7200

Пульт сигнализации VIPER


Viper(434MHz) - 210HV, 350HV, 650XV, 850XV, 550HF, 600HF, 700HF, 800HF
Viper(302MHz) - Viper Ultra 700, 800, 900

Пульт сигнализации AVITAL


Avital (434MHz) - 21000, 2200, 4000, 4100, 4200, 4300, 4400

Пульт сигнализации VALET


Valet (434MHz) 450R, 562T, 561R, 712T, 716T

Пульт сигнализации HORNET


Hornet (434MHz) - 740, 742

Пульт сигнализации RATTLER


Rattler (434MHz) - 110D, 210D, 310D, 369D

Пульт сигнализации STEEL STOPPER


Steal Stopper (302MHz) - 90

Пульт сигнализации CRIME STOPPER


Crime Stopper CS-2004TW2, CS-409TX

Пульт сигнализации MARS


Mars 22, 32, 33

Пульт сигнализации BULLDOG - 710-P


Bulldog 2010 (mini car alarm, without voice messaging system)
Bulldog 2020
Bulldog 2010 (mini car alarm, with 7message talking alarm)

Пульт сигнализации BULLDOG - 711-P


Bulldog RS102, RS202, Deluxe 12, Deluxe 22, Deluxe 62, 1100E, 1200E & 1300E

Пульт сигнализации ASTROSTART


Astrostart RS-113LED

Пульт сигнализации ASTROSTART


Astrostart 1004

Пульт сигнализации MONGOOSE


Mongoose Immobilizer Card

Пульт сигнализации MS MAGIC SYSTEM


Система универсального радиоуправления.
Брелок для управления четырехканальным модулем.

Пульт сигнализации MS MAGIC SYSTEM

Пульт сигнализации WHISTLER


Whistler AT-600
Очень распространенный брелок, служит универсальной заменой для многих сигнализаций.

Пульт сигнализации EXUS


Exus V2 Street

Пульт сигнализации KINGS GUN


Kings Gun

Пульт сигнализации MICRO


Micro 6008, 8008, DLR4, DL4HD

Пульт сигнализации INTERNET


Internet AS100, AS200

Пульт сигнализации BARRACUDA


Barracuda EX33HN, EX77HN, EX88HN

Пульт сигнализации EXPIDATOR


Expidator 3HN, 7HN, 8HN

Пульт сигнализации MICRO


Micro START C2001, START C2002, START C2003

Пульт сигнализации MEGATRONIX


Megalarm MT-4

Пульт сигнализации KEYMASTER

Пульт сигнализации MEGATRONIX

Пульт сигнализации GALAXY


ASTRA200
ASTRA600 5-BUTTON
Astra 50

Пульт сигнализации MEGATRONIX


Megalarm MT-4

Пульт сигнализации MEGATRONIX


Megatronix MEGA 3004

Пульт сигнализации EXCLUSIVE


Exclusive BGA104R

Пульт сигнализации CARBINE


Carbine PL-40C, PL-50C, PL-60C, PLUS 3000C, PLUS 4000C, PLUS 5000C

Пульт сигнализации CHECKMATE


Пульт сигнализации COMMANDER


Модели KD-200PC, KD-500, KD-70SPC

Пульт сигнализации BULLDOG

Пульт сигнализации MEGATRONIX


Megatronix MEGA 670L

Пульт сигнализации MEGATRONIX


Megatronix MEGA 3100 / VS 3125

Пульт сигнализации MEGATRONIX


Megatronix MEGA 3100 / VS 3125, MEGA 2000, 250, 2500, 3700

Пульт сигнализации MEGATRONIX


Пульт сигнализации KEYMASTER


Модели Megalarm – MTK4

Пульт сигнализации MARKSMAN 4bb

Пульт сигнализации MAGICAR

Пульт сигнализации MAGICAR


Magicar M-1500 II

Пульт сигнализации MAGICAR


Magicar M-8000 III

Пульт сигнализации MAGIC ALARM


Magic Alarm

Пульт сигнализации EXUS


Exus V10 Expert

Пульт сигнализации EXUS


Exus V10

Пульт сигнализации FANTOM


Fantom F115

Пульт сигнализации EAGLE MASTER


Eagle Master TX-4P 950EEK

Пульт сигнализации FANTOM


Fantom F-115

Пульт сигнализации PHANTOM


Phantom Voyager

Пульт сигнализации EASYCAR


Easycar EZ-4000, EZ-4000II, EZ-5000, EZ-5600

Пульт сигнализации CENTURION


Centurion Xabre

Пульт сигнализации GENERIC


Generic RS-7K
Generic RS-7K2

Пульт сигнализации JABLOTRON


Jablotron CA-320 Akcent

Пульт сигнализации JOY


JOY-702, 802

Пульт сигнализации Пульт PATROL LINE

Пульт сигнализации SHERIFF


Sheriff ZX-910 (дополнительный брелок)

Пульт сигнализации SCHER KHAN


Scher Khan Jungle

Пульт сигнализации Пульт TR-1220

Пульт сигнализации MS MAGIC SYSTEM


MS-320 Baikal, MS-360, MS-360T, MS-370 Stalker LAN, MS-Baikal 2, MS Stalker 450, MS-400T

Пульт сигнализации PHARAON


Pharaon V17i

Пульт сигнализации PYTHON


Python 1400XPL

Пульт сигнализации VIPER 434MHz


Viper 160XVL

Пульт сигнализации PYTHON


Python 502, 702, 902, 1090, 3102P, 3302P, 5501P

Пульт сигнализации VIPER 434MHz


Viper 1002, 3002, 5002, 7900
Viper 160XVL, 562VL

Пульт сигнализации TERMINATOR


Terminator Two Way Lux

Пульт сигнализации ALPINE


Alpine SEC-150R, SEC-100S, SEC-8028

Пульт сигнализации Пульт UNGO

Пульт сигнализации CODE ALARM


Code Alarm Elite Competition, Elite 4000, Elite 6000

Пульт сигнализации TEXALARM


Texalarm AVA 51

Пульт сигнализации PANTERA


Pantera CLR - 5200

Installation manual

System Layout

System Specifications

System Arming

The system will ignore all trigger inputs for 25 seconds after the second arming chirp / light flash

Alarm Trip Cycle

Siren will sound for 30 seconds The alarm will then ignore all trigger inputs for 10 seconds, then rearm The siren will not sound again until another intrusion is detected

Panic

Pressing any two buttons on the remote transmitter activates the Panic feature Panic duration is 30 seconds Pressing any button on the remote transmitter de-activates the Panic feature

Sensors
  • Power and Ground are active at all times on Sensor Port 1
  • Ground on Sensor Port 2 is active only when the alarm is fully armed
  • Pressing the ARM button again within 5 seconds of arming the system will deactivate the Lite-Touch inputs on Sensor Ports 1 and 2, and the trigger input on Sensor Port 2 The siren will chirp three times when these inputs are deactivated These inputs will remain deactivated until the alarm is disarmed then rearmed.
  • 10 Lite-touch trips within one arming period will cause the alarm to ignore any further lite-touch inputs until it is disarmed, then rearmed.
  • 4 Full-trigger trips within one arming period will cause the alarm to ignore any further full-trigger inputs until it is disarmed then rearmed .
Automatic Arming

If the Automatic Arming option is enabled, the alarm will automatically arm and disable the vehicle starter 20 seconds after the ignition is turned off and the last door is closed, or 2 minutes after the alarm is disarmed and not manually re-armed

Automatic Immobilization

If the Automatic Arming option is not enabled, the alarm will automatically disable the vehicle starter 20 seconds after the ignition is turned off and a door is opened, or 2 minutes after the alarm is disarmed and not re-armed.

Valet
  • Valet Mode prevents the alarm from arming automatically, and prevents automatic immobilization Enter Valet Mode by pressing the DISARM button on the remote transmitter with the vehicle ignition on.
  • In Valet Mode, the LED will double-flash when the vehicle ignition is on.
  • In Valet Mode, the LED will flash once every 1/2-second when the vehicle ignition is off.
  • Exit Valet by pressing any button on the remote transmitter with the vehicle ignition off.
Illuminated Entry

The Illuminated Entry Output is activated for 60 seconds after the alarm is disarmed.

Trunk Release / Auxiliary Output

The Trunk Release / Auxiliary Output is activated by pressing and holding DISARM or ARM (selectable) on the remote transmitter The output duration lasts as long as the button is held (up to 45 seconds).

Door Locks
  • The Door Lock / Unlock Outputs are activated when the alarm is armed and disarmed. Duration is .6 seconds or 6 seconds (selectable).
  • The Door Lock Output is activated when all doors are closed and the vehicle ignition is turned on (this option can be turned off).
  • The Door Unlock Output is activated when the vehicle ignition is turned off (this option can be turned off).
  • If the Trunk Release / Auxiliary Output is set to Button 2, pressing and holding Button 1 will activate the Door Lock Output for as long as the button is held (up to 45 seconds).
  • If the Trunk Release / Auxiliary Output is set to Button 1, pressing and holding Button 2 will activate the Door Unlock Output for as long as the button is held (up to 45 seconds).
Trip Identification
  • Trip ID identifies the specific zone that triggered the alarm system.
  • Upon returning to the vehicle, press DISARM. If the siren chirps 4 times, the alarm was triggered.
  • Press DISARM again. The siren will chirp a number of times, indicating the violated zone.
# of Chirps Zone
1Sensor 1
2Sensor 2
3Door, Hood, Trunk
4Ignition
Auxiliary Output 1

Auxiliary Output 1 is activated at any time by pressing OPTION 1 on the remote transmitter. The output is activated as soon as the button is pressed, and will continue to operate for a preset time. The preset time duration is programmable to .6, 6, 12, or 24 seconds.

Note: Pressing the OPTION 2 button while Auxiliary Output 1 is active will turn off Auxiliary Output 1.

Auxiliary Output 2

Auxiliary Output 2 is activated at any time by pressing OPTION 2 on the remote transmitter. The output is activated as soon as the button is pressed, and will continue to operate for a preset time. The preset time duration is programmable to .6, 6, 12, or 24 seconds.

Note: Pressing the OPTION 1 button while Auxiliary Output 2 is active will turn off Auxiliary Output 2.

Feb 11, 2018 - Egyptian Ak 47 Serial Numbers. I picked up my MISR S/A back around 2001 or so.CALL Century and give them the serial number and they will. Egyptian ak 47 serial numbers

Installation

Remove all fuses from the wire harness before installation.

A. Siren (#20 ORANGE)
  • Mount bell housing downwards.
  • Use at least two (2) screws to secure siren to mounting location.
  • Connect siren BLACK wire to module ORANGE wire.
  • Connect siren RED wire to a fused +12-volt source.
B. 12V+ Main Feed (#22 RED)
  • Connect at vehicle battery or at main 12-volt lead at ignition switch harness.
    Circuit Verification - Target wire registers voltage at all times.
C. 12V+ Switched Feed (#17 Lt. BLUE)
  • Connect at switched 12-volt lead at ignition switch harness.*
    Circuit Verification - Target wire registers voltage when ignition key is turned to the ON position and START position.

* If you are connecting the optional 2-Cut immobilizer, make sure to connect the #17 Lt. BLUE wire closest to the ignition switch. See page 12 for further details.

D. Ground (#11 BLACK)
  • Attach to grounded metal point of vehicle chassis.
    Note: When installing multiple components (such as an alarm and remote starter), ground the units separately.
E. Starter Interrupt (WHITE/RED and WHITE on 2-pin Connector)
  • Connect to vehicle starter wire at ignition switch harness.
    Circuit Verification - Target wire registers voltage only when ignition key is turned to the START position.

    Circuit Verification after starter wire is cut:

    • KEY SIDE of starter wire registers voltage when ignition key is turned to the START position.
    • MOTOR SIDE of starter wire registers no voltage.

Note: Some vehicles have two starter wires. If so, cut both and connect to the alarm module. Refer to Vehicle Wire Color and Location Chart.

F. Door Pin Switches (#8 YELLOW or #19 WHITE)
Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location, or verify the vehicle wire using the following guideline:
  • Positive Systems - Target wire registers voltage when any door is opened.
  • Negative Systems - Target wire registers ground when any door is opened.
G. Illuminated Entry (#4 YELLOW and #3 YELLOW/BLACK)
  • Circuit Verification - Target wire is usually the door pin switch wire Refer to section F for verification guideline
  • Connect #4 Lt YELLOW wire to the target wire
  • Connect #3 YELLOW/BLACK wire to +12V if the door system is positive.
  • Connect #3 YELLOW/BLACK wire to ground if the door system is negative.
H. Parking Lights (#2 ORANGE/BLACK and #1 BLACK/WHITE)
  • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location or verify the vehicle wire using the following guideline
    • Positive Systems - Target wire registers voltage when parking lights are on
    • Negative Systems - Target wire registers ground when parking lights are on
  • Connect #2 ORANGE/BLACK wire to the target wire
  • Connect #1 BLACK/WHITE wire to +12V if the system is positive.
  • Connect #1 BLACK/WHITE wire to ground if the system is negative.
I. Hood /Trunk Pin Switch (#7 Lt. GREEN)
  • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit location or install a pin switch and connect to the module #7 Lt. GREEN wire
J. Power Door Locks: #14 Lt. BLUE, #13 Lt. BLUE/BLACK, #10 RED/BLACK, #6 RED/WHITE, #16 GREEN, #15 GREEN/BLACK
  • Circuit Verification - Refer to Vehicle Wire Color and Location Chart for circuit type and location
Type 1 - Positive 3-Wire Door Lock System
Type 3 - Negative 3-Wire Door Lock System
Type 2 - Positive 5-Wire Door Lock System
Type 4 - Vacuum Door Lock System
K. Status Indicator (#18 GRAY)
  • Locate a visible location on the dash with 1' clearance behind the location
  • Drill a 1/4 hole and snap the status indicator in place
  • Connect the status indicator BLACK wire to the module GRAY wire
  • Connect the status indicator RED wire to a fused +12-volt source
L. Trunk Release / Aux. Output (#5 VIOLET and #12 TAN)

Note: This output can be programmed to act as a trunk release output or auxiliary output (See Programming Selectable Options - next page )

  • Trunk Release Refer to Vehicle Wire Color and Location Chart for circuit type and location or verify the vehicle wire using the following guideline
  • Circuit Verification:
    • Positive Systems Target wire registers voltage when the trunk / hatch is opened using the vehicle button
    • Negative Systems Target wire registers ground when the trunk / hatch is opened using the vehicle button
  • Auxiliary Output Determine the polarity needed for the accessory
  • Connect #12 TAN wire to the target wire
  • Connect #5 VIOLET wire to +12V if the system is positive
  • Connect #5 VIOLET wire to ground if the system is negative *

* lf connecting to a negative trunk release system a specific connection location may be required Refer to Vehicle Wire Color and Location Chart

M. Auxiliary Outputs 1 and 2 (#21 PINK and #9 BLACK/GREEN)
  • Determine the polarity needed for the accessory
    • Negative Polarity Needed: Connect #21 PINK or #9 BLACK/GREEN to the accessory input (Note 500ma max outputs)
    • Positive Polarity Needed: Add a SPST or SPOT relay (not included) and connect as shown
N. Impact Detector
  • Mount the impact detector to the steering column or to a sturdy wire harness
  • Plug the impact detector into SENSOR PORT 1 on the module
O. Armed Output (BLACK on Sensor Port 2)
  • Connect to a device requiring a ground signal when the alarm system is armed

System Power-Up

  • Check all connections and wire routing
  • Turn ignition to the ON position
  • Replace all fuses in the module harness
  • Turn the ignition off

Programming Selectable Options

  1. Make sure the system is disarmed and the ignition is off
  2. Without starting the vehicle turn the ignition ON, OFF, ON, OFF, then ON, at 1/2-second intervals

    After two (2) seconds the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure If the correct code is entered the siren will chirp three times indicating entry into the Selectable Options Mode.

  3. Press Button 1 on a programmed remote transmitter to begin option selections
Option Number and DescriptionBold Type Indicates Factory SettingsStatus Indicator ONStatus Indicator OFF
1 Doors lock when all doors are closed and vehicle ignition is turned onYESNO
2 Doors unlock when vehicle ignition is turned off YESNO
3 Lock / Unlock Output Duration6 sec1/2 sec
4 Trunk/Aux Output is Activated by Pressing and Holding ARM or DISARMARMDISARM
5 Siren chirps when arming and disarming YESNO
6 System arms automatically 20 seconds after last door is closedYESNO
7 Auxiliary Output 1 Timer Programming See Timer Programming Section Below
8 Auxiliary Output 2 Timer Programming

Timer Programming

Auxiliary Outputs 1 and 2 can be programmed to send a specific timed output when their respective buttons are pressed.

When programming Option number 7 or 8, the LED will flash a number of times, indicating the current timed output setting.

# of FlashesOutput Duration
10,6 seconds
26 seconds
312 seconds
424 seconds

Pressing DISARM on a programmed transmitter advances to the next option.

To Exit Selectable Options Mode, turn the vehicle ignition On, then Off.

Testing the Alarm System

1. Arming and Disarming / Sensor Override
Close all doors and press ARM
  • All doors lock
  • Siren chirps two times / parking lights flash two times
  • Status indicator turns on
Within 5 seconds press ARM again
  • Siren chirps three times (sensor override)
Press Disarm
  • All doors unlock
  • Siren Chirps once / parking lights flash
  • Status indicator turns off
  • Courtesy light turns on (if connected)
2. Alarm Triggering / Starter Interrupt /Trip ID / Lock Options
Arm system. Wait 30 seconds then open door
  • Siren sounds / parking lights flash
With siren sounding attempt to start vehicle
  • Vehicle will not start
Wait until siren stops then press DISARM
  • Siren chirps / parking lights flash 4 times (System was triggered)
Press DISARM again
  • Siren chirps three times (System was triggered by door)
Close doors and attempt to start vehicle
  • Vehicle starts
  • Doors lock (if Ignition Lock Option is activated)
Turn ignition off
  • Doors unlock (if Ignition Unlock Option is activated)
3. Trunk Release /Auxiliary Option
Press and hold ARM or DISARM (depending on options programming)
  • Trunk opens or aux device activates
4. Panic
Press two buttons for one second
  • Siren sounds / parking lights flash for 30 seconds. Press either button to stop
5. Automatic Arming (Test only if Automatic Option is activated)
Enter vehicle and close doors Turn ignition on for five seconds then turn off. Exit vehicle and close doors.
  • Alarm arms 20 seconds after door is closed
6. Valet
With system disarmed turn ignition on, then press DISARM
  • Status Indicator Flashes twice (enters Valet Mode)
Turn ignition off
  • Status indicator flashes every 1/2 second
Close all doors and press ARM
  • Flashing stops and system arms
7 Auxiliary Outputs (Test if connected)
Press OPTION 1 on the remote transmitter
  • Accessory connected to Aux. Output 1 activates
Press OPTION 2 on the remote transmitter
  • Accessory connected to Aux. Output 2 activates
Testing the Emergency Disarm Procedure
  1. Exit the vehicle close all doors and arm the alarm system Wait 30 seconds, then trigger the alarm by opening a door
  2. With the siren sounding enter the vehicle and turn the ignition to the ON position

After two (2) seconds the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure

If the correct code is entered, the alarm system will disarm.

Adjusting the Impact Detector

  1. Turn the white knob on the impact detector clockwise until it stops, then turn counter clockwise approximately 1/4 of a turn.
  2. Test the sensitivity by arming the alarm system, waiting 30 seconds then slapping various parts of the vehicle with an open hand.
    • A light slap should cause the siren to emit a warning chirp.
    • A heavier slap should trigger the alarm.
  3. Adjust the sensitivity until the desired setting is achieved.

If your system includes the optional 2-Cut Immobilizer, refer now to the installation instructions. Return to this section when installation and testing of the Immobilizer are complete.

Antenna Placement /Mounting the Module

1a. If the module has a short antenna (approx 8) keep the antenna as straight as possible and route away from vehicle harnesses

1b. If the module has a long antenna completely uncoil the antenna and route up the nearest front window pillar to the headliner Be careful not to pinch the antenna under vehicle panels or route near moving parts.

2. For optimum performance allow the clear plastic portion of the antenna to remain exposed in the corner of the window or behind the rear-view mirror.

IMPORTANT!!!

INDUSTRIA ARGENTINA 1, 2, 5, 6: Recorded and mixed between August 10 and 22 of 1988 at Estudios Buenos Aires Records (Argentina) (from ) 3, 4, 7, 11: Recorded and mixed between October of 1989 and February of 1990 at Estudios Buenos Aires Records (Argentina) (from ) 8 to 10: Recorded at Estudio Panda (Argentina), mixed at Sound City Studios, Los Angeles, California, USA between September and October of 1991. Rata blanca grandes canciones 2000 descargar.

Before mounting the module, write the alarm code (found on the back ol the module) in the space provided on the front of the Owner's Manual. FAILURE TO DO SO COULD CAUSE YOUR CUSTOMER TO BE STRANDED SHOULD THE REMOTE TRANSMITTER EVER FAIL!

3. Mount the module using supplied long tie wraps Make sure the module and harnesses are clear of moving vehicle parts.

Immobilizer Installation

Note: Immobilizer wires are numbered at the ends for identification. When connecting the wires, cut off the numbered sections to enhance security.

1. Code Input (BLACK/PINK)
  • Connect to #21 PINK wire from the alarm module harness.

Note: The #21 PINK wire can connect to both the Immobilizer AND an auxiliary relay.

2. Ground
  • Attach to grounded metal point of vehicle chassis.
3. 12V+ Switched Power
  • Connect at switched 12-volt lead at ignition switch harness.

IMPOTANT! If you are using CUT 1 or CUT 2 to interrupt the vehicle ignition wire, connect the alarm module #17 Lt. BLUE and the immobilizer #3 wire closest to the ignition switch.

4. Cut 1 In/Out Wires (max. 30A)
  • Use these wires to interrupt vehicle ignition or other wires.
    • Cut the target wire in half.
    • Connect one half of the target wire to one of the CUT 1 wires
    • Connect the other half of the target wire to the other CUT 1 wire.
      Note: The CUT 1 wires are interchangeable.
5. Cut 2 In/Out Wires (max. 30A)
  • Use these wires to interrupt vehicle ignition or other wires.
    • Cut the target wire in half.
    • Connect one half of the target wire to one of the CUT 2 wires
    • Connect the other half of the target wire to the other CUT 2 wire.
      Note: The CUT 2 wires are interchangeable.
Power-Up and Testing of the Immobilizer

The immobilizer learns the code of the alarm system when it is first connected and the ignition is turned on. From this point on, the immobilizer is 'matched' to that particular alarm. If the alarm module is changed, or if the immobilizer is removed and connected to a different alarm, the immobilizer will not operate (the vehicle will not start.)

  1. Make sure the alarm is disarmed.
  2. Turn the vehicle ignition to the ON position.
  3. Observe the LED on the immobilizer.
    • If the alarm is connected, the LED will turn on.
    • If the alarm is not yet connected, the LED will flash:
      • If the immobilizer has never been connected to an alarm, the LED will emit a double-flash pattern.
      • If the immobilizer has been connected to an alarm system, the LED will emit a slow, steady blink.
    • If the alarm is connected, but the immobilizer was previously connected to another alarm system, the LED will emit a rapid flash pattern, meaning that it has received an improper code. The vehicle will not start.
  4. Verify that the vehicle starts.

Note: The immobilizer interrupts the selected wires whenever the alarm system interrupts the starter wires. Verify that the wires are disabled under the conditions listed in the Automatic Arming and Automatic Immobilization sections of System Specifications.

Mounting the Immobilizer
  • Mount the immobilizer using the supplied long tie wraps. Be sure that all connections are well-insulated.

Programming Remote Transmitters

Note: Each system module has four 'slots', or memory locations, to store remote transmitter codes, giving it the ability to operate from up to four remote transmitters. For proper operation, a transmitter code must be stored into each memory slot. When using less than four transmitters, follow the suggested programming parameters:

  • One Remote Transmitter - Program four (4) times
  • Two Remote Transmitters - Program each remote transmitter two (2) times
  • Three Remote Transmitters - Program one remote transmitter twice, and each remaining remote transmitter once.
  1. Make sure the system is disarmed and the ignition is off.
  2. Without starting the vehicle, turn the ignition ON, OFF, then ON, at 1/2-second intervals.

    After two (2) seconds, the status indicator will begin flashing for Code Entry. Follow the Code Entry Procedure (below). If the correct code is entered, the siren will chirp twice, indicating entry into the Transmitter Programming Mode.

  3. Wait 5 seconds. Press Button 1 on the remote transmitter to be programmed. The siren will chirp once, indicating that the system has 'teamed' that transmitter.
  4. Repeat step 3 for any additional remote transmitters or transmitter codes.
  5. Exit the Transmitter Programming Mode by turning the vehicle ignition on, then off. Test all remote transmitters to ensure that they work properly.

Code Entry Procedure

  1. Enter the Code Entry Mode by following the steps in the Programming Remote Transmitters, Programming Selectable Options, or Testing the Emergency Disarm Procedure sections of this manual.

    The status indicator will begin flashing for Code Entry.

  2. Look at the first number in the code. Allow the status indicator to flash the corresponding number of times as the first number in'the code.
  3. After the status indicator has flashed the corresponding number of times, turn the vehicle ignition off. The first number has been entered.
  4. Turn the ignition back to the ON position. The status indicator will again begin flashing. Repeat the procedure in steps 2 and 3, this time using the second number in the code.
  5. Repeat steps 2 and 3 for the third and fourth numbers in the code.
  6. After the fourth number has been entered correctly, the alarm will disarm, or enter the desired programming mode.

Note: If you enter an incorrect digit, turn the vehicle ignition off, then on. When the status indicator begins to flash, re-enter the code from the beginning.

Example: The code is 2314.

  1. Enter the Code Entry mode.
  2. Allow the status indicator to flash two (2) times. After the second flash, turn the vehicle ignition off.
  3. Wait one second, then turn the ignition on.
  4. Allow the status indicator to flash three (3) times. After the third flash, turn the vehicle ignition off.
  5. Enter the third and fourth numbers in the same manner.
26.12.2001
⇐ ⇐ Lame_enc.dll For Audacity 2.0.0
⇒ ⇒ Free.midi Style Koplo New Psr